Blog

Our 10 years of Lithium Iron Phosphate experience shared within thousands of articles, hundrends of tests and examples.

29.Jan 2018
 
". "LFP battery discharged to ZERO volts

Warning: DOMDocument::loadHTML(): Tag figure invalid in Entity, line: 2 in /var/www/ev-power_eu/views/knowledgebase.php on line 601 Warning: DOMDocument::loadHTML(): Tag figure invalid in Entity, line: 3 in /var/www/ev-power_eu/views/knowledgebase.php on line 601
Blog EVPower
LFP battery discharged to ZERO volts Question: I have installed a LFP battery in my car. But when I came today to the car, the car was completely dead and all electronics stopped working. What is wrong? Answer: What you describe may happen with the car. When the car is parked, over some days, then some equipment will discharge the battery to complete emptiness (full deep over-discharge). This may happen when the small “inside” lamp is by mistake left “on”, or when the door is not closed properly. It may also happen that the radio was left “on” – but silent, or some other equipment drained the battery (e.g. alarm system that turned on for some reason). In some cases the driver may accidentally forget the main headlights on, and the battery will be depleted just in a few hours.
   ...more >>

22.Dec 2017
 
". "Packing of Sinopoly cells

Blog EVPower
The photos show the packing of the Sinopoly cells. The cells are packed in wooden boxes that meet for the transport of dangerous goods.
he ADR safety regulations
   ...more >>

22.Dec 2017
 
". "Production fault - reversed polarity

Blog EVPower
Sometimes a mistake may happen…. This photo shows a that has a reversed polarity marking. The problem was cased during the final part of the production, as the outer sleeve with the polarity symbols (plus/minus signs) was put in opposite direction. The cell is completely OK, only the marking is reversed. This real situation shows that even , a faulty product may slip out. This case also shows the need for the final responsibility of checking during the installation of the cells. There is always need to check everything to the very last detail and not relying just on signs and marking. In this case we have honored the warranty and replaced the cell with another new cells with proper marking.
he ADR safety regulations
G-LFP 20AH cell
fter a multiple checking of the production
   ...more >>

21.Dec 2017
 
". "Become the battery specialist and visit GWL Power in Prague for the Battery Technology Training Seminar

Blog EVPower
The Battery Technology Training Seminar – March 9th 2017, Prague, Czech Republic Become the battery specialist and visit GWL/Power in Prague for a battery technology training seminar. GWL/Power invites you to come, meet members of GWL and Sinopoly team face to face, learn more about LiFePO4 technology and other related topics. The training includes the presentations, discussions and technology demonstrations.
he ADR safety regulations
G-LFP 20AH cell
fter a multiple checking of the production
heck here for more details
   ...more >>

21.Dec 2017
 
". "The voltage levels for BMS

Blog EVPower
he BMS provided by GWL are primarily designed for the LFP cells (2.0V to 3.8V). Some BMS models support the LTO and Li-Ion cells as well. - supports LFP and Li-Ion, does not support LTO - supports LFP, Li-Ion and LTO
he ADR safety regulations
G-LFP 20AH cell
fter a multiple checking of the production
heck here for more details
MS123Smart
MS2405
   ...more >>

20.Dec 2017
 
". "Checking and checking again

Blog EVPower
Any system can have a failure or an irregular operation. That is why it is important to perform multiple tests and verifications of each installation. With battery systems the possibility of a failure or malfunction is multiplied by the number of the cells or the complexity of the installation. For a system with 2 cells, with 20 cells and with 200 cells the possibility of “problem” will be multiplied 2 times, 10 times and even 100 times. The photo shows an example of a failure of the BMS system in a 4 cell installation. The BMS module reports a voltage and temperature that is not correct. Making a measurement of the cell proves the failure condition of the setup. In this case, caused by a defective BMS module that needs a replacement. Our recommendation: the battery pack should have regular inspections and verifications performed.
he ADR safety regulations
G-LFP 20AH cell
fter a multiple checking of the production
heck here for more details
MS123Smart
MS2405

20.Dec 2017
 
". "AutarcTech - energy storage partner in Germany

Blog EVPower
The AutarcTech company is using the cells from GWL to make the energy solution. Learn more about AutarcTech and their products. AutarcTech GmbHTechnologiepark 191522 AnsbachDeutschlandTel. 0981 9878 7374 AutarcTech GmbH, founded 2010 in Ansbach, Germany, designs and produces Lithium batteries and Batterie-Management-Systems (BMS). Our next-generation technology sets us apart from the standard battery storage systems. Active balancing significantly increases life-expectancy of the lithium cells. This process is automatically performed when required during the entire charge and discharge cycle. The effective useable capacity of the battery is maintained. Because the energy from one cell is transferred to another, the balancing process does not rely on wasting energy to heat and becomes far more efficient.
he ADR safety regulations
G-LFP 20AH cell
fter a multiple checking of the production
heck here for more details
MS123Smart
MS2405
ww.autarctech.de
   ...more >>

18.Dec 2017
 
". "GWL/Power Simple Battery Management Board 4 cells (12V/16A)

Blog EVPower
The is designed for a simple protection of the 12V battery packs using the 3.2V LFP cells. The SBM has higher rating resistors (bigger ones) so that the balancing current is little bigger. For even higher balancing currents we suggest adding the or modules. The examples of the installation are here: , , .
he ADR safety regulations
G-LFP 20AH cell
fter a multiple checking of the production
heck here for more details
MS123Smart
MS2405
ww.autarctech.de
16H
BM1 module
2V battery
4V battery
8V battery
   ...more >>

18.Dec 2017
 
". "BMS123 Smart with Victron inverters

Blog EVPower
Check the connection of the with thetThe Victron inverters: These are equipped with AUX I/O (allow to charge) and Temp sense (allow to discharger ports. The charge/discharge contact functionality is available only in case the .
he ADR safety regulations
G-LFP 20AH cell
fter a multiple checking of the production
heck here for more details
MS123Smart
MS2405
ww.autarctech.de
16H
BM1 module
2V battery
4V battery
8V battery
40
MS123 Smart
ithium assistant function is activated
   ...more >>
19 visitors online.
All Rights reserved © 2019 EVPower a.s.